Smart1.0 is a two way active full range system housing a 1in. (25mm) exit compression driver mounted on a 60deg. H x 40deg. V constant directivity horn and a 10in. (250mm) low-mid transducer loaded in bass reflex enclosure.
Highest grade audio accuracy is guaranteed by fixed frequency switch mode output stage, avoiding any intermodulation artifact, and by the new "Control Plus" board allowing to achieve +6 dB more in terms of Signal-to-Noise Ratio.
The Smart amplifier module is an extremely compact solution: power supply, output stage, DSP board and connectors are all included in a single, small, lightweight and protected chassis, and the perfect compatibility with the other Smart Series products allows to minimize efforts for mechanical development of different products.
As for all Smart products, the Smart1.0 amplifier module is shaped and controlled using the DSP boards available to design the sound of the loudspeaker with a large set of processing algorithms.
Versatility is a key attribute of the Smart1.0.
Significant construction criteria, combined with the latest technologies and innovative materials, ensure a great reliability.
The system can be as well matched with the Loud Professional Smart Subwoofers range, boosting its LF extension.
Applications: Theaters, Conference Halls, Concert Halls, Large Scale Discos, Clubs &
Products || VH Full-Range || VH Monitor || VH Line-Array || VH Subwoofer || VH Micro || Smart Series || FocusEight
Two-way active powered system
|Transducers:||10in. Low-Mid Reflex|
|1in. exit compression driver Mid-Hi Horn|
|Frequency range:||80Hz-18kHz +/- 4dB (-10dB @ 65Hz)|
|Power handling:||LMF/MHF: 700/100 Watts Program|
|Maximum SPL:||124dB continuous, 130dB peak|
|Nominal coverage:||60°H/40°V (@-6dB point)|
|Audio Input connectors:||Female XLR input, male XLR link output Neutrik|
|Mains connectors:||Powercons In & Out|
|Class:||Two channel switch mode, Class D|
|Power supply:||Universal, regulated switch mode|
|Nominal power requirement:||100-240 V ±10%, 50-60 Hz|
|Operating voltage:||90V - 264V|
|Thermal||0°- 45°C - 32°- 113°F|
|Gain:||38 dB (voltage1 gain x40)|
|Input sensitivity:||11.15V / 3.43 dBu|
|Max input level:||15 dBu|
|Frequency response:||20 Hz - 20 kHz (±0.5 dB) @ 1 W, 8 Ω|
|S/N ratio:||> 112 dB (20 Hz - 20 kHz, A weighted)|
|THD+N:||< 0.05% from 1 W to full power (typically < 0.01%)|
|IMD:||< 0.02% from 1 W to full power (typically < 0.005%)|
|Input impedance:||10 kΩ balanced|
|Slew rate:||50 V/μs @ 8Ω, input filter bypassed|
|Damping factor:||> 500 @ 100 Hz|
|AD Converter:||Dual 24 bit 48 kHz Tandem® architecture with 118 dBA S/N, THD < 0.02% (20 Hz - 20 kHz)|
|DA Converter:||Dual 24 bit 48 kHz Tandem® architectureb with 115 dBA dynamic range, THD < 0.02% (20 Hz - 20 kHz)|
|Internal precision:||28 bit data path with 56 bit inner processing|
|Firmware:||Update via ethernet port or RS485|
|Latency:||0.644 ms fixed latency architecture|
|Crossover:||Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct|
|Delay:||up to 10 ms per output|
|Limiters:||Peak limiter, RMS limiter, frequency dependent RMS limiter|
|Shell:||18mm 13 Ply birch|
|Finish:||Black or white Polyurea coated paint|
|Grille:||Powder coated Steel|
Integrated amplifier module
|Two channels professional amplifier with DSP on board|
On board Programmable DSP
ProNET 485 Networking dialog card
RS232 USB converter
Dedicated Two-way Full-Range powered system<<
Efficient Class D amplifier <<
Onboard programmable DSP, programming connector <<
Remote control & Networking <<
Four programmable DSP presets <<
Clip limiter and permanent signal limiter <<
Preset led and preset selector push button <<
Input volume potentiometer <<
Powercons In & Out <<
Portable Sound & light weight <<
Two handles & 8 x M8 threated inserts for easy setup <<
PCP Polyurea coated paint <<
Protection Bag <<Accessories <<
Applications: Theatre || Congress || Club || Portable
The Company reserves the right to alter any specifications to the products and published documentations.